Laserfiche WebLink
201804403 <br /> PRINSCO GOLDFLO"P1 PE SPECIFICATION <br /> PRINSCO <br /> Scope <br /> This specification designates the requirements for 4-through 60-inch I.D. Prinsco GOLDFLO®pipe for use in <br /> gravity-flow drainage applications. <br /> Pipe Requirements <br /> Prinsco GOLDFLO pipe shall have annular exterior corrugations with a smooth interior allowing for a <br /> Manning's"n"design value of.012 and shall meet the following standards: <br /> • 4-through 10-inch shall meet AASHTO M252,Type S <br /> • 12-through 60-inch shall meet ASTM F2306 or AASHTO M294, Type S <br /> Materials <br /> GOLDFLO pipe and fabricated fittings shall be manufactured using High Density Polyethylene(HOPE) <br /> meeting the minimum requirements of cell classification of 435420C for 4-through 10-inch diameters and <br /> 4354000 for 12-through 60-inch diameters,as defined and described in ASTM D3350 except the carbon <br /> black content should not exceed 4%. <br /> The HOPE pipe material for 12-through 60-inch diameter pipe shall be tested for slow crack growth <br /> resistance using the notched constant ligament-stress(NCLS)test as specified in sections 9.5 and 5.1 of <br /> AASHTO M294 and ASTM F2306,respectively. Average failure time of the five test specimens shall not be <br /> less than 24 hours. <br /> Joint Performance <br /> GOLDFLO pipe shall be joined using soil tight joints meeting AASHTO M252, M294,or ASTM F2306. <br /> Gaskets,when used, shall be made of polyisoprene meeting the requirements of ASTM F477 and shall be <br /> installed by the manufacturer. An approved joint lubricant, available from the manufacturer,shall be applied <br /> to the bell and gasket,of gasketed joints,during installation. GOLDFLO joints shall be assembled in <br /> accordance with the manufacturer's requirements. <br /> Fittings <br /> Fittings shall meet the requirements of AASHTO M252, M294,or ASTM F2306. Standard fittings are <br /> available as listed in the Prinsco Product Catalog and custom fittings may be fabricated to customer specific <br /> requirements. <br /> Physical Pipe Dimensions <br /> Nominal ID Approximate Corrugation Approximate Min.Pipe stiffness CI(in) OD(in) Length(ft) Pitch(In) Welghtifoot(lb) Deflection(pal) <br /> 4" 4.6 20 .67 0.5 50 <br /> 6" 7.1 20 .80 1.0 50 <br /> 8" 9.5 20 1 00 1 7 50 <br /> 10" 11.9 20 1.30 2 3 50 <br /> 12" 14.3 10,20 2 00 3.1 50 <br /> 15" 17.5 10,20 2.67 4.5 42 <br /> 18" 21.6 11,20 3.00 6.5 40 <br /> 24" 28,4 11,20 4.00 11.0 34 <br /> 30" 35 11,20 4.00 14.6 28 <br /> 36" 41.0 11,20 4.00/4.70* 19.0 22 <br /> 42" 47.5 11,20 6.00/430* 25 20 <br /> 48" 54 11,20 6.00/4.70' 30 18 <br /> 60" 66.5 20 590 40 14 <br /> *Contact your Prinsco sales representative to determine actual corrugation pitch. <br /> Page 1 of 2 <br /> 1717 16'"St NE J 3`1 Floor j Willmar,MN 56201 (500.992.1725 i <br /> C Prinsco, Inc. 11/09 <br />